1. 1. Question
    When an EIGRP-enabled router uses a password to accept routes from other EIGRP-enabled routers, which mechanism is used?
    •  EIGRP authentication
  2. 2. Question
    What is the purpose of using protocol-dependent modules in EIGRP?
    •  to accommodate routing of different network layer protocols
  3. 3. Question
    If all router Ethernet interfaces in an EIGRP network are configured with the default EIGRP timers, how long will a router wait by default to receive an EIGRP packet from its neighbor before declaring the neighbor unreachable?
    •  15 seconds
  4. 4. Question
    Which statement describes a characteristic of the delivery of EIGRP update packets?
    •  EIGRP uses a reliable delivery protocol to send all update packets.
  5. 5. Question
    Which two EIGRP packet types are sent with unreliable delivery? (Choose two.)
    •  acknowledgment
  6. 6. Question
    Which destination MAC address is used when a multicast EIGRP packet is encapsulated into an Ethernet frame?
    •  01-00-5E-00-00-0A
  7. 7. Question
    What is identified within the opcode of an EIGRP packet header?
    •  the EIGRP message type that is being sent or received from a neighbor
  8. 8. Question
    An administrator issues the router eigrp 100 command on a router. What is the number 100 used for?
    •  as the autonomous system number
  9. 9. Question
    Why would a network administrator use a wildcard mask in the network command when configuring a router to use EIGRP?
    •  to exclude some interfaces from the EIGRP process
  10. 10. Question
    What information does EIGRP maintain within the routing table?
    •  only successors
  11. 11. Question
    Which table is used by EIGRP to store all routes that are learned from EIGRP neighbors?
    •  the topology table
  12. 12. Question
    Which command or commands must be entered on a serial interface of a Cisco router to restore the bandwidth to the default value of that specific router interface?
    • no bandwidth
  13. 13. Question
    Which three metric weights are set to zero by default when costs in EIGRP are being calculated? (Choose three.)
    •  k2
    •  k4
    •  k5
  14. 14. Question
    A new network administrator has been asked to verify the metrics that are used by EIGRP on a Cisco device. Which two EIGRP metrics are measured by using static values on a Cisco device? (Choose two.)
  15. 15. Question
    Refer to the exhibit. Which two networks contain feasible successors? (Choose two.)
    CCNA3 v6.0 Chapter 6 Exam 003
    CCNA3 v6.0 Chapter 6 Exam 003
  16. 16. Question
    A network administrator wants to verify the default delay values for the interfaces on an EIGRP-enabled router. Which command will display these values?
    •  show interfaces
  17. 17. Question
    Refer to the exhibit. R3 has two possible paths to the network. What is the reported distance of the feasible successor route?
    CCNA3 v6.0 Chapter 6 Exam 002
    CCNA3 v6.0 Chapter 6 Exam 002
  18. 18. Question
    Refer to the exhibit. R2 has two possible paths to the network. What would make the alternate route meet the feasibility condition?
    CCNA3 v6.0 Chapter 6 Exam 001
    CCNA3 v6.0 Chapter 6 Exam 001
    •  a reported distance less than 3523840
  19. 19. Question
    Which two factors does an EIGRP router use to determine that a route to a remote network meets the feasible condition and is therefore loop-free? (Choose two.)
    •  the reported distance on a neighbor router
    •  the feasible distance on the local router
  20. 20. Question
    Which configuration is necessary to ensure successful operation of EIGRP for IPv6?
    •  The no shutdown command is required within the router configuration mode.​
  21. 21. Question
    Fill in the Blank. Use the abbreviation.
    EIGRP uses the protocol   RTP       to deliver EIGRP packets to neighbors.​
  22. 22. Question
    Fill in the blank.
    In an EIGRP topology table, a route that is in a/an     active                state will cause the Diffusing Update Algorithm to send EIGRP queries that ask other routers for a path to this network.
  23. 23. Question
    Order the precedence in which an EIGRP router would choose the router ID. (Not all options are used.)
    CCNA3 v6.0 Chapter 6 Exam 01
    CCNA3 v6.0 Chapter 6 Exam 01
  24. 24. Question
    Match the correct version of EIGRP with the EIGRP features. (Not all options are used.)
    CCNA3 v6.0 Chapter 6 Exam 02
    CCNA3 v6.0 Chapter 6 Exam 02
  25. 25. Question
    Open the PT Activity. Perform the tasks in the activity instructions and then answer the question.
    Which code is displayed on the web server?